garett t2 help

[mike dahl]

i was at the junk yard and a guy came up to me and said he had a garett t2 for $100 and said everything was tight no shaft play but had a oil problem i need to know what its worth and whats wrong with it,

and another question i was pulling a turbo of a new yorker need to know what stage it is it says garett but is the size of my mitsubishi

[mike dahl]

also i need to know if this will fit my car

T3/T4 Wet Floating Bearings Turbocharger!!
Stage-3 Turbo
Oil Cool
CNC Machined Flanges 4Bolt Designed fit most After market Mainfolds.
25 to 35 Psi Peak Power Performance Output Capability.(factory warranty).
Designed Usable for External Wastegate Applaction Or Use A T3/T4 Adapter with Internal Wastegate
5 bolt pattern flange for Downpipe
Compressor Specs:
3" Compressor Inlet
2.000" or 50.55mm inducer
3.000" or 76.20mm Major
2" Compressor Outlet
M12 Type Compressor Housing
Compressor .50 A.R.
Compressor 57 Trim
6 Blade Type Turbine
Turbine Specs:
T3 Type Turbine flange
T3 5 bolt flange
Turbine .64 A.R.
Turbine Trim
2.207" Minor and 2.567" Major Propellar
T3 Twin Entry Turbine Housing
2.25" Exducer
11 Blade Type Turbine

thinking about buying it for the summer

[tryingbe]

Turbo have oil problem = trash. Either leaking oil or starve of oil, neither is good.

New Yorker would have a TI Garrett turbo.

Ebay turbo, XS power, XYZ turbo, T3/T4 brand turbo = 50% working time...

[mike dahl]

would a rebuild kit take care of the oil problem

[tryingbe]

Do you know what exactly is this "oil" problem?
If it is too far gone, wheels could have contact the housings and be beyond repair.

[mike dahl]

nope i dont know what the oil problem is but the explained that it has no play at all and the blades are good

[mike dahl]

the guy selling the turbo says he thinks the seals are bad

[mike dahl]

will the chrysler new yorker garett t1 bolt up to my mitsubishi t1 manifold with no problems

[stargazer7467]

yeah but there might be oil line issues

[ol"blue]

On an '88 Lancer I replaced the Mitsu with a Garret. Lines fit fine. Car only had 34k on it though. Higher miles might just replace lines as insurance.

[Sittn86]

G-Pop shop has 4-pc carbon seal kits for about $100. Give them a call & they'll tell you what you need. I think a rebalance is only $45. If nothing's touched, it won't need that, though. To use the TI Garrett on an 88+ TI car, you'd need the TII style compressor housing without the 90° outlet. TU sells them.

[mike dahl]

i figured i might have some problems because the car i took the turbo off had the throttle body hooked to the turbo so i figured it spun the opposite way,all the oil lines look the same, the garett looks like it has more lines going to it.whatever help you can give me let me know first time putting a different turbo on a car.

[Sittn86]

The turbos spin the same way, early turbo I's used a draw-through intake system. They have the same # of lines, but you'll have to bend the oil lines to make them fit. It's probably best to replace them, though.

Read:

Donovan's Dodge Garage

www.DempseyBowling.com

Gus Mahon Homepage

Welcome to FWD Performance, Inc. has the lines for ~$100

forwardmotioninc (dot) com has great stuff, too

turbosunleashed (dot) com has the blow-through compressor outlet that you need.

[mike dahl]

would the mitsu lines fit the garett.i know stupid question but everytime i think something doesnt fit it sometimes does.how much boost can i run this t1 garett at with a intercooler

[Sittn86]

Yes, they will fit, but they'll require some bending because they're at a different angle. At ~$100, it's cheap insurance, so I'd replace them. Are you reading this stuff? And in case you missed this too, a Turbo I turbocharger WILL NOT fit with its original compressor outlet. You need a conversion from Turbos Unleashed.