Turbo Dodge Forums : Turbo Dodge Forum for Turbo Mopars, Shelbys, Dodge Daytona, Dodge SRT-4, Chrysler PT Cruiser, Omni and more! - Reply to Topic
Engine Management, Fuel, Spark, EGTs, and Air/Fuel Ratios This forum includes general electrical, modification, tuning, repair, replacement, identification and restoration of all components mentioned above including SMEC, SBEC, Logic Modules, aftermarket engine management, etc. Nitrous oxide posts go in here. This is the place

Thread: Microsquirt and 2000 Dodge Magnum info? Reply to Thread
Title:
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:
 
   

Register Now



In order to be able to post messages on the Turbo Dodge Forums : Turbo Dodge Forum for Turbo Mopars, Shelbys, Dodge Daytona, Dodge SRT-4, Chrysler PT Cruiser, Omni and more! forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

Member names may only be composed of alpha-numeric characters. (A-Z and 0-9)

!!ATTENTION ADVERTISERS!! If you intend on advertising anything on this forum, whatsoever, you are required to first contact us here . Additionaly, we do NOT allow BUSINESS NAMES unless you are an Authorized Vendor. If you own a business, and want to do sales on this site via posting or private message, you will need to follow the rules. Shops, Stores, Distributors, Group Buys without being authorized will see your account terminated.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in










  Additional Options
Miscellaneous Options

  Topic Review (Newest First)
10-18-2018 12:43 PM
Prochargedmopar
Re: Microsquirt and 2000 Dodge Magnum info?

Thanks for the info.
I now see the other reply and got to the part in the manual where the settings are.
I'll have to get everything wired up and then come back for more questions later.

Man, After seeing your pics I sure wish I still had my 84 Turbo Z car.
Back in the late 90's I rebuilt the engine and turbo.
Installed kb hyper pistons and total seal rings. Turned boost up to 10ish from factory 7.
Crunched front bumper and hood. Car sat for years and finally let it go to the wrecker.....Bummer.
That car was cool.
10-16-2018 12:23 PM
tryingbe
Re: Microsquirt and 2000 Dodge Magnum info?

I'm not familiar with V8 so my information could be wrong.

8 tooth wheel should work fine, and someone already give you hardware settings at MSextra website.

With Microsquirt and a V8, you will not have any extra outputs left over since you'll need those for ignition. I used my Microsquirt two outputs for fan control and a/c cut off relay.

You'll need to use a 2 wire high idle valve or 2 wire pwn idle controller. Stock 4 wire iac will not work.

MS has a total of 36 wires, I'm sure you can figure it out.

I first separated the engine harness, labeled every wire, kept the ones I needed and cut the one I didn't.


I used a Qaudspark to drive my 420A coil, not cheap but it is simple and easy.



Mounted my 420A coil onto plugged distributor.
10-16-2018 10:22 AM
Prochargedmopar Yes, I just got registered version of TS Ultra and MegaLog HD.
Originally after some short studies before purchase I figured I could use all factory sensors with batch fire/injection and wasted spark.
After watching ALL of Whittles Utube vids I see the 8 tooth wheel doesn’t give much resolution for idle speeds.

I’m just not sure what hardware settings to do use with micro V3.
I will continue reading the manuals while I get this engine installed.
If I have to buy a 36-1 wheel or other things I may just pull the sniper off my truck and put this on a BB 451 engine instead.
All depends on if I can figure this out before I get the magnum engine done/installed.
10-15-2018 05:06 PM
tryingbe
Re: Microsquirt and 2000 Dodge Magnum info?

I presume this is you?
Megasquirt Support Forum (MSEXTRA) ? Hardware Settings for Micro on 5.9 Dodge? (View topic)

Nobody use Megatune anymore. TunerStudio and MegaLog Viewer are the software to use.

What method are you going to use the read the crank signal? Stock crank sensor? Adding a 36-1 wheel? What are you going to use for ignition? Wasted spark?
10-14-2018 03:04 PM
Prochargedmopar Sorry,
Its a 2000 Model 5.9 Dodge magnum engine I plan to put in my 73 Dodge dart with 904 trans.
10-13-2018 11:36 PM
tryingbe
Re: Microsquirt and 2000 Dodge Magnum info?

2000 Dodge Magnum? What engine does it use?
10-13-2018 06:28 AM
Prochargedmopar
Microsquirt and 2000 Dodge Magnum info?

Does anyone know of a write-up or thread that shows info. on this particular combination?
I found the classic ignition section on DIYauto but it seems vague on the magnum engines.
My main questions are the settings for crank/cam in tunerstudio.
Basemap to get the engine started would be sweet but I’ve read its best to start from scratch.
Thanks for any and all links.

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

 
For the best viewing experience please update your browser to Google Chrome