Turbo Dodge Forums : Turbo Dodge Forum for Turbo Mopars, Shelbys, Dodge Daytona, Dodge SRT-4, Chrysler PT Cruiser, Omni and more! - Search Results
Advanced Search
Showing results 1 to 25 of 500
Search took 0.05 seconds.
Search: Posts Made By: byghtn
Forum: Transmission, Suspension, Brakes, Tires & Wheels   07-05-2016, 10:17 PM
Replies: 3
Views: 516
Posted By byghtn
Re: L-body manual rack rebuild

Good to hear of your success!

I'm interested in seeing your progress!
Forum: Turbo Dodge Help   06-14-2016, 09:20 AM
Replies: 13
Views: 493
Posted By byghtn
Re: Forged crank or not?..

Looks to be forged.....

Grinder marks & an apparent wide parting line usually indicate a forged piece.

This can be faked but why go to the effort of that???

Probably forged.
Forum: Turbo Dodge Help   06-13-2016, 07:54 PM
Replies: 13
Views: 493
Posted By byghtn
Re: Forged crank or not?..

It is hard to say, your current photo angles are not helpful for this kind of I.D.

Show a close up of the areas circled in red.(please....)
Forum: Transmission, Suspension, Brakes, Tires & Wheels   06-10-2016, 06:20 PM
Replies: 5
Views: 325
Posted By byghtn
Re: Suspention parts.

Are the photos actual photos or representative photos?

Maybe in real life there is no difference????

Good Luck on your decisions...
Forum: Parts For Sale   06-08-2016, 06:51 AM
Replies: 2
Views: 413
Posted By byghtn
Re: Rear disc, polybushings mounts, wheel studs, MBC, muffler, bov

I'm interested!

How much to Atl Ga 30341 and how to pay?
Forum: Turbo Dodge Help   06-02-2016, 07:10 PM
Replies: 20
Views: 1,053
Posted By byghtn
Forum: Parts For Sale   06-02-2016, 07:02 PM
Replies: 4
Views: 773
Posted By byghtn
Re: Accufab rail mounted AFPR

Message 2 says SOLD
Message 3 says BUUUMP

Is it sold or not?

If not sold, I would like to own it.

Please advise....
Forum: Electrical   06-01-2016, 09:51 PM
Replies: 10
Views: 484
Posted By byghtn
Re: Bulkhead Disconnect L Body Vehicles

I thought exactly the same thing several times....
Apparently the bolt re-tightens a little while you are pulling. I am not saying it is your problem, only that it has been my problem several times...
Forum: Electrical   06-01-2016, 08:54 PM
Replies: 10
Views: 484
Posted By byghtn
Re: Bulkhead Disconnect L Body Vehicles

The BH connector won't just fall apart into your hands, you have to pull pretty hard sometimes---

Also

Sometimes after you think the bolt is loose, you will pull & pull, then loosen the bolt...
Forum: Electrical   05-31-2016, 09:01 PM
Replies: 10
Views: 484
Posted By byghtn
Re: Bulkhead Disconnect L Body Vehicles

If you find you have to get into the BH connector, you will find a central bolt that holds the 2, (1/2's) together.

Once you separate the 1/2's, there are master keys that hold the individual wire...
Forum: Engine - General, Exhaust & Induction   05-26-2016, 04:45 PM
Replies: 9
Views: 713
Posted By byghtn
Re: Small N/A head mods?

Will the HEMI oil seals restrict the oil flow to the guides causing accelerated guide wear in street/daily driver conditions?
Forum: Engine - General, Exhaust & Induction   05-26-2016, 09:23 AM
Replies: 9
Views: 485
Posted By byghtn
Re: cruise control install

My son and I are adding cruise control to a wire harness that never had it in an '88 SMEC into '84-"L-Body" conversion. If this type of upgrade is your interest/goal, not just l-body, LMK.....
Forum: Parts For Sale   05-23-2016, 10:05 AM
Replies: 65
Views: 3,710
Posted By byghtn
Re: Parting out 90 Daytona LOTS OF STUFF

I would like the FSM's and PTD manuals please.

Price delivered to 30341 Atl Ga.
Media Mail discounts should be applicable with USPS.

Thanks
Forum: Transmission, Suspension, Brakes, Tires & Wheels   05-22-2016, 11:50 PM
Replies: 9
Views: 472
Posted By byghtn
Re: K-Frame Boot Air Deflector Shield Purpose

How about to protect PS lines from radiant heat soak after shut-down?
Forum: Engine - Turbo & Block   05-20-2016, 08:36 PM
Replies: 5
Views: 636
Posted By byghtn
Re: 2.2 engine

You may have a 2.2L engine with a 2.5L computer??
Forum: Parts For Sale   05-19-2016, 07:30 AM
Replies: 51
Views: 3,452
Posted By byghtn
Re: parting out 1987 shelby charger

Do you have the back half of the wire harness?
I'm looking for the green connector under the dash to the tail lights, wire harness assy.

Do you have this??
Forum: Parts For Sale   05-17-2016, 08:38 PM
Replies: 6
Views: 491
Posted By byghtn
Re: SBEC Harness

Done!:thumb:

Please send a tracking number when you ship the wire harness.

Thanks.
Forum: Parts For Sale   05-16-2016, 10:16 PM
Replies: 6
Views: 491
Posted By byghtn
Re: SBEC Harness

I'll take it!!

Please PM how to pay....
Forum: Mitsubishi V6 engines   05-15-2016, 08:37 PM
Replies: 10
Views: 553
Posted By byghtn
Re: Intake air temp sensor hole size?

It looks like you need to tap this hole a little deeper to allow the tip of the sensor to screw in deeper to measure the AIR temp????

Just a thought.
Forum: Parts For Sale   05-15-2016, 08:29 PM
Replies: 6
Views: 491
Posted By byghtn
Re: SBEC Harness

I'm interested....
How much shipping to ATL Ga 30341???

Thanks
Forum: Transmission, Suspension, Brakes, Tires & Wheels   05-15-2016, 08:12 PM
Replies: 7
Views: 1,328
Posted By byghtn
Re: SLH front brakes for the L-body

I believe the 2-pin calipers are "ATE" not "KH", and are not cross compatible.
Keep looking.....



Can you provide the parts store name & P/N's that you are referring to??
Advance online shows...
Forum: Transmission, Suspension, Brakes, Tires & Wheels   05-09-2016, 12:54 AM
Replies: 7
Views: 451
Posted By byghtn
Re: Flare Wrench Size for Master Cylinders?

I almost always use a 4" Genuine Vise Grip to disconnect stubborn brake lines.....

Your mileage may vary.

Good Luck & BE SAFE!
Forum: Transmission, Suspension, Brakes, Tires & Wheels   05-07-2016, 09:11 PM
Replies: 3
Views: 186
Posted By byghtn
Re: Click coming from front end when braking in reverse?

The brake pads typically have small anti-rattle 'springs' that hold the pad in the 'forward' direction. Braking in reverse will cause the pad to move backward in the bracket.

Maybe this is your...
Forum: Turbo Dodge Help   05-05-2016, 09:49 PM
Replies: 6
Views: 441
Posted By byghtn
Re: ENGINE NEEDED ASAP!!! Michigan

Remembering a conversation with Shel-Game, he told me the FFV ECM would be difficult to re-program because of "3-D" fuel & spark tables.

I think you should aim for a 2.5 unless you want to be...
Forum: Engine Management, Fuel, Spark, EGTs, and Air/Fuel Ratios   05-03-2016, 08:26 PM
Replies: 6
Views: 1,743
Posted By byghtn
Re: Need pinout diagrams

The '91 ECM is SBEC and the '89 is SMEC, and they are not compatible for changing a few pins around.

What you can do --easily?-- is use a '91 Turbo SBEC and add 5 or 6 wires to the existing TBI...
Showing results 1 to 25 of 500

 
Forum Jump
 
For the best viewing experience please update your browser to Google Chrome