Search Results for ‘tbi’

hey new to posting on this thread, I have a stock 1989 dodge w150 with a 318 tbi, was wondering if anyone could help me with what I need to add a small turbo only pushing 5-10 psi, trying to do it on a cheaper budget for now and maybe upgrading it later

Finally think I’m dunn, or for now anyway... Picked up this gem a couple years back, it’s a 2.2 TBI Auto, long roof. I immediately thought “it needs a lift kit”... So that’s what I did! Went through a lot of trials and tribulations of parts swapping till finally dialing it in “correctly”. Lift...

Does anybody have a link to swapping out the pins on these? I believe both harnesses have to be chopped and rewired together because the Omni has a 40 pin connector and the Daytona has a 50 pin. I haven't verified this for sure yet but any information would be appreciated. This is keeping my...

I am in the process of converting my 91 tbi shadow to turbo2. I am using an 89 smec because this was the easiest computer for me to get. I used the existing wiring harness. I found dealership wiring diagram books. However injectors 1 and 2 refuse to fire. the car has spark fuel pressure. the...

Hey there! Need the big stamped steel oil curtain that's under all the TBI valve covers. Let me know! Please and thank you!

I am doing a TBI to tII swap. I need the pinout diagrams for a 91 dodge shadow TBI. As well as an 89 turbo shadow. I am very close to being done just need help with the final wiring. Thank you in advance.

I have to do a a computer and harness swap in my 92 spirit auto 2.5 TBI, I'm putting in a T1 computer and harness, just wanted to know if there were anything I should know or be aware of? Anything tricky? Or pretty straight forward??? Thanks in advance for any info or tips!!!

Ok 92 spirit tbi auto, I'm actually keeping it N/A but going to use a flex fuel spirit computer and intake, fuel rail, fpr, and injectors. But for all intensive purposes we'll just say TBI to T1 because I know it's been done. My question is; is there anyway to wire in the injectors to my 92 tbi...

Very long story short: I have an 87 Shelby Daytona that has been in storage for 6 years. Shot a rod the day I bought it after saving to buy my first car. At this point I just want it back on the road. If I pick up a 2.2/2.5 NA motor, can I bolt on the MPFI manifold and use the same PCM/Logic...

Soooo... i have my 88 dodge Omni. I am trying to run the OE TBI setup, but with a turbo. I believe i have everything that should be needed, but need help/verification with the oil/coolant/wastegate lines. I have an adapter made to bolt onto the TBI unit for the turbo to force air through. I have...

I am about to do a rebuild on my bottom end. I am wondering where a good place to be to get a good quality reman crankshaft. I found one from Marshall Engines on Rock Auto. is this a good one, or does somebody think there is a better one?

going to try posting this here . I have multiple questions , don't over complicate the answers 1 : what do you think is a middle of the road compression ratio for a 2.5 motor , 5 speed in a 1989 mini (take into consideration the weight of this vehicle)? #2 : now how much boost would u apply...

someone please help!!! i am going to be doing a rebuild on my 89 dodge dytona's 2.5L tbi. i really need the internal specifications for the entire motor. also, if nobody ca help me with this, then i want your opinion on whether the haynes or chilton would be better fr my need, and why you think so

I'm looking for an 89^ Omni or Horizon airbox setup. Let me know if you have anything. Thanks!

My 92 daytona 2.5 na bogs when you step on it most of the time, sometimes to the point of stalling (automatic). It's been ported with a 2in exhaust and I cut that ugly and restrictive air box off, leaving the filter. I've heard that you can drill the throttle body out to get more fuel, but is it...

Are there any carbs or throttle bodies that are bigger than factory that matches the bolt pattern? If not, what would be a good one to use with an adapter?

Date: 29th September 2012 Username: ShelGame Full Name: Rob Lloyd City, State, Zip: Whitmore Lake, MI 48189 Contact: PM Price: $10 shipped Description: Column lock with key from a '90 Daytona. Not sure what else it will fit...

i have a concern that i trying to figure out. i have a 87 daytona shelby that i bought and have come to realize that i just do not have time to redo the floors and brake lines fuel lines ect. The motor and trans are in great shape runs great and trans shifts good ect. (floors are non-existant) i...

Ive seen a lot of post about the TBI cam upgrade but none explaining what to do, what its dose to add power and a install procedure, with how to time it and what to time it at. :shrug: So any pictures and how too would be much helpful. Im not new to turbo dodges just never done this before...