Turbo Dodge Forums banner

wastegate

  1. Performance Mod NEW! Turbos Unleashed 3"Swingvalve

    Parts For Sale
    I have a brand new never on the car TU 3" Swingvalve for sale. The TU 3" swingvalve provides 78% more exhaust flow area over the factory Garrett 2.25" Swingvalve and 44% more exhaust flow area over the 2.25" swingvalves used on turbo vehicles after '89. Dyno results have proven an additional 5...
  2. Few Turbo 2 parts

    Parts For Sale
    Just parts I had laying around the garage that I do not need anymore. Everything is fine. Open to all offers. PM me if you're interested in anything. May add more stuff later on. All shipping costs on your end. Pay Pal preferred. Thanks. 1) Turbo 2 exhaust manifold: Still has all 4 studs...
  3. wastegate and turbo charger

    Engine - General, Exhaust & Induction
    I have a 1986 dodge daytona turbo z 2.2 turbo, and im having boosting problems. The car boosts fine but the boost gauge wobbles as it does this and im not for sure if the wastegate is working properly. I was going to test the wastegate and noticed that a pipe that goes from the bottom of the...
  4. head revised,Turbo overboost-injector's shut down?

    Engine - Turbo & Block
    I have a small problem I'ts a 2.2 turbo 2,My car had some idle problem's,we had to take the head,intake,exhaust and turbo off,the head has been revised ,Also a new gaskets set fore everything that came off,(also a new fuel pump) We've put everything back in place and while test driving i can...
  5. boosting problem with 88 shelby lancer T2

    Turbo Dodge Help
    Its fine driving normally and the boost goes to 11psi and it stayes there until around 4500-5000rmp then my boost jumps to around 15 psi then my turbo cuts hard and shakes my car it slowed down so fast, im worried its gonna damage my engine, its all stock except a cold air intake and a blowoff...
  6. 87 2.2l turbo boost problems?

    Turbo Dodge Help
    Bought the car put it on the road. runs fine but when you step on it it will buck anytime u past 5 pounds of boost and anything under 5 pounds. But if its at 5 pounds it runs fine. I dont know whats up. Cars completely stock. Had a code for wastage solenoid but i dont know if that has anything...
  7. disconnected wastegate

    Engine - Turbo & Block
    i tryed disconnecting my wastegate on my 01 dodge cummins and it seems like it didnt give me anymore boost. any ideas?
  8. T1 turbo, wastegate and rebuilt transmission 86 dodge shelby charger

    Parts Wanted
    T1 turbo, wastegate and rebuilt transmission for a 1986 Dodge Shelby Charger
  9. Some of the ways to prevent your wastegate actuator arm from seperating

    Turbo Dodge Help
    Some of the ways to prevent your wastegate actuator arm from becoming disconnected from the swing valve; 1)....Go to napa and get a replacement E clip not a C. Part # is 7/32 E clip. 2)....Some folks on here tyewrap them together. 3)....Some have used SAFETY-WIRE to wrap around it...
  10. WANTED: ACTUATOR for chrysler lebaron.

    Parts For Sale
    Hi. I have a 1984 chrysler lebaron. Turbo. I need the wastegate actuator for it. Please text me at 8168632995. Or leave a message on my voicemail for it. Also, I'm not looking to pay more than 20 or 30 dollars for it, but we can negotiate. Thank you!
  11. USA wastegate sol. for 88 lebaron

    Parts Wanted
    I'm looking for a wastegate sol. assembly for an 88 lebaron. Anyone got one their willing to part with? :First TD:
  12. ECU Boost?

    Turbo Dodge Help
    I'm wondering how exactly ECU controlled boost works. In all my previous turbo vehicles, boost is limited only by the wastegate spring. When manifold pressure surpasses the static force of the spring it is forced open and out goes the exhaust pressure. So a 14psi spring would allow 14lbs. of...
  13. help with TII vac lines!

    Board Discussion
    hi, i have a 91 daytona shelby that has an aftermarket garrett t2 turbo. when i bought the car, it worked great with 12 psi boost. but after i replaced the head gasket, i can only get 5 psi because the waste gate is always bypassing the exhaust. . . is there anyone out there that has a vacc...
Top